H3c-technologies H3C WX6000 Series Access Controllers Manuel d'utilisateur Page 99
- Page / 179
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
7-7
Follow these steps to enable the trap function:
To do… Use the command… Remarks
Enter system view
system-view
—
Enable the trap function globally
snmp-agent trap enable
[
configuration
|
flash
|
standard
[
authentication
|
coldstart
|
linkdown
|
linkup
|
warmstart
] * |
system
|
wlan
]
Optional
Enabled by default.
Enter interface view
interface
interface-type
interface-number
Required
Enable the trap function of
interface state changes
enable snmp trap updown
Optional
Enabled by default.
To enable an interface to send linkUp/linkDown traps when its state changes, you need to enable the
trap function of interface state changes on an interface and globally. Use the enable snmp trap
updown command to enable the trap function on an interface, and use the snmp-agent trap enable
[ standard [ linkdown | linkup ] * ] command to enable this function globally.
Configuring Trap Parameters
Configuration prerequisites
To send traps to the NMS, make the following preparations:
z Basic SNMP configurations have been completed. These configurations include version
configuration: community name is needed when SNMPv1 and v2c are adopted; username and MIB
view are needed if SNMPv3 is adopted.
z A connection has bee established between the device and the NMS, and they can operate each
other.
Configuration procedure
After traps are sent to the SNMP module, the SNMP module saves the traps in the trap queue. You can
set the size of the queue and the holding time of the traps in the queue, and you can also send the traps
to the specified destination host (usually the NMS).
Follow these steps to configure trap parameters:
To do… Use the command… Remarks
Enter system view
system-view
—
Configure target host attribute for
traps
snmp-agent target-host
trap
address
udp-domain
{ ip-address
|
ipv6
ipv6-address } [
udp-port
port-number ]
params
securityname
security-string [
v1
|
v2c
|
v3
[
authentication
|
privacy
] ]
Optional
To send the traps to the NMS, this
command is required, and you
must specify ip-address as the IP
address of the NMS.
Configure the source address for
traps
snmp-agent trap source
interface-type interface-number
Optional
- Configuration Guide 1
- All Rights Reserved 2
- Trademarks 2
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Obtaining Documentation 6
- Technical Support 6
- Documentation Feedback 6
- Table of Contents 8
- 2 Typical Network Scenarios 13
- Unified Switch Networking 14
- 3 Feature Matrixes 15
- 4 Command Matrixes 29
- Introduction 61
- Configuring Ping 61
- Tracert 64
- System Debugging 65
- 6 NTP Configuration 69
- NTP Message Format 71
- Operation Modes of NTP 72
- Symmetric peers mode 73
- Broadcast mode 73
- NTP Configuration Task List 74
- NTP Configuration Examples 83
- delay disper 89
- Root delay: 40.00 ms 89
- 7 SNMP Configuration 93
- SNMP Protocol Versions 94
- MIB Overview 94
- SNMP Configuration 95
- Configuring SNMP Logging 97
- Configuring SNMP Traps 98
- Configuring Trap Parameters 99
- Network requirements 101
- Configuration procedure 101
- 8 MIB Style Configuration 104
- 9 RMON Configuration 105
- RMON Groups 106
- Alarm group 107
- Private alarm group 107
- Configuration Procedure 109
- Configuration Prerequisites 109
- Information Center Overview 115
- System Information Format 120
- 11 NQA Configuration 136
- Basic NQA concepts 139
- NQA Configuration Task List 140
- Configuring the NQA Server 141
- Enabling the NQA Client 141
- Creating an NQA Test Group 142
- Configuring DHCP Tests 143
- Configuring DNS Tests 144
- Configuring FTP Tests 145
- Configuring HTTP Tests 146
- Configuring UDP Jitter Tests 147
- Configuration prerequisites 148
- Configuring UDP jitter tests 148
- Configuring SNMP Tests 149
- Configuring TCP Tests 150
- Configuring UDP Echo Tests 150
- Configuring UDP echo tests 151
- Configuring Voice Tests 152
- Scheduling an NQA Test Group 157
- NQA Configuration Examples 158
- 12 Index 178
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX6000 Series Access Controllers
(85 pages)
(13 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.112 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels