H3c-technologies H3C WX6000 Series Access Controllers Manuel d'utilisateur Page 148
- Page / 179
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11-13
Configuration prerequisites
UDP jitter tests require cooperation between the NQA server and the NQA client. Before you start UDP
jitter tests, configure UDP listening services on the NQA server. For more information about UDP
listening service configuration, see
Configuring the NQA Server.
Configuring UDP jitter tests
Follow these steps to configure UDP jitter tests:
To do… Use the command… Remarks
Enter system view
system-view
—
Enter NQA test group view
nqa
entry
admin-name
operation-tag
—
Configure the test type as UDP
jitter and enter test type view
type udp-jitter
Required
Configure the destination address
of UDP packets
destination ip
ip-address
Required
By default, no destination IP
address is configured.
The destination IP address must
be the same as that of the listening
service on the NQA server.
Configure the destination port of
UDP packets
destination port
port-number
Required
By default, no destination port
number is configured.
The destination port must be the
same as that of the listening
service on the NQA server.
Specify the source port number of
UDP packets
source port
port-number
Optional
By default, no source port number
is specified.
Configure the size of the data field
in each UDP packet
data-size
size
Optional
100 bytes by default.
Configure the string to be filled in
the data field of each probe packet
data-fill
string
Optional
By default, the string is the
hexadecimal number
00010203040506070809.
Configure the number of probe
packets to be sent during each
UDP jitter probe operation
probe packet-number
packet-number
Optional
10 by default.
Configure the interval for sending
probe packets during each UDP
jitter probe operation
probe packet-interval
packet-interval
Optional
20 milliseconds by default.
Configure the interval the NQA
client must wait for a response
from the server before it regards
the response is timed out
probe packet-timeout
packet-timeout
Optional
3000 milliseconds by default.
Configure the source IP address
for UDP jitter packets
source ip
ip-address
Optional
By default, no source IP address is
specified.
The source IP address must be the
IP address of a local interface. The
local interface must be up;
otherwise, no probe packets can
be sent out.
- Configuration Guide 1
- All Rights Reserved 2
- Trademarks 2
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Obtaining Documentation 6
- Technical Support 6
- Documentation Feedback 6
- Table of Contents 8
- 2 Typical Network Scenarios 13
- Unified Switch Networking 14
- 3 Feature Matrixes 15
- 4 Command Matrixes 29
- Introduction 61
- Configuring Ping 61
- Tracert 64
- System Debugging 65
- 6 NTP Configuration 69
- NTP Message Format 71
- Operation Modes of NTP 72
- Symmetric peers mode 73
- Broadcast mode 73
- NTP Configuration Task List 74
- NTP Configuration Examples 83
- delay disper 89
- Root delay: 40.00 ms 89
- 7 SNMP Configuration 93
- SNMP Protocol Versions 94
- MIB Overview 94
- SNMP Configuration 95
- Configuring SNMP Logging 97
- Configuring SNMP Traps 98
- Configuring Trap Parameters 99
- Network requirements 101
- Configuration procedure 101
- 8 MIB Style Configuration 104
- 9 RMON Configuration 105
- RMON Groups 106
- Alarm group 107
- Private alarm group 107
- Configuration Procedure 109
- Configuration Prerequisites 109
- Information Center Overview 115
- System Information Format 120
- 11 NQA Configuration 136
- Basic NQA concepts 139
- NQA Configuration Task List 140
- Configuring the NQA Server 141
- Enabling the NQA Client 141
- Creating an NQA Test Group 142
- Configuring DHCP Tests 143
- Configuring DNS Tests 144
- Configuring FTP Tests 145
- Configuring HTTP Tests 146
- Configuring UDP Jitter Tests 147
- Configuration prerequisites 148
- Configuring UDP jitter tests 148
- Configuring SNMP Tests 149
- Configuring TCP Tests 150
- Configuring UDP Echo Tests 150
- Configuring UDP echo tests 151
- Configuring Voice Tests 152
- Scheduling an NQA Test Group 157
- NQA Configuration Examples 158
- 12 Index 178
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX6000 Series Access Controllers
(85 pages)
(13 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels