H3c-technologies H3C WX6000 Series Access Controllers Manuel d'utilisateur Page 156
- Page / 179
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
11-21
To do… Use the command… Remarks
Configure the hold time of statistics
groups
statistics hold-time
hold-time
Optional
120 minutes by default.
z The NQA statistics collection function is not supported in DHCP tests.
z If you use the frequency command to set the frequency between two consecutive tests to 0, only
one test is performed, and no statistics group information is collected.
Configuring the History Records Saving Function
The history records saving function enables the system to save the history records of NQA tests. To
view the history records of a test group, use the display nqa history command.
In addition, you can configure the following elements:
z Lifetime of the history records—The records are removed when the lifetime is reached.
z The maximum number of history records that can be saved in a test group—If the number of history
records in a test group exceeds the maximum number, the earliest history records are removed.
Follow these steps to configure the history records saving function of an NQA test group:
To do… Use the command… Remarks
Enter system view
system-view
—
Enter NQA test group view
nqa
entry
admin-name operation-tag
—
Enter NQA test type view
type
{
dhcp
|
dns
|
ftp
|
http
|
icmp-echo
|
snmp
|
tcp
|
udp-echo
|
udp-jitter
|
voice
}
—
Enable the saving of the
history records of the NQA
test group
history-record enable
Required
By default, history records of
the NQA test group are not
saved.
Set the lifetime of the history
records in an NQA test group
history-record keep-time
keep-time
Optional
By default, the history records in
the NQA test group are kept for
120 minutes.
Configure the maximum
number of history records
that can be saved for a test
group
history-record number
number
Optional
By default, the maximum
number of records that can be
saved for a test group is 50
Configuring Optional Parameters for an NQA Test Group
Optional parameters for an NQA test group are valid only for tests in this test group.
Unless otherwise specified, the following optional parameters are applicable to all test types.
Follow these steps to configure optional parameters for an NQA test group:
- Configuration Guide 1
- All Rights Reserved 2
- Trademarks 2
- Preface 3
- GUI conventions 4
- Symbols 4
- Network topology icons 4
- Obtaining Documentation 6
- Technical Support 6
- Documentation Feedback 6
- Table of Contents 8
- 2 Typical Network Scenarios 13
- Unified Switch Networking 14
- 3 Feature Matrixes 15
- 4 Command Matrixes 29
- Introduction 61
- Configuring Ping 61
- Tracert 64
- System Debugging 65
- 6 NTP Configuration 69
- NTP Message Format 71
- Operation Modes of NTP 72
- Symmetric peers mode 73
- Broadcast mode 73
- NTP Configuration Task List 74
- NTP Configuration Examples 83
- delay disper 89
- Root delay: 40.00 ms 89
- 7 SNMP Configuration 93
- SNMP Protocol Versions 94
- MIB Overview 94
- SNMP Configuration 95
- Configuring SNMP Logging 97
- Configuring SNMP Traps 98
- Configuring Trap Parameters 99
- Network requirements 101
- Configuration procedure 101
- 8 MIB Style Configuration 104
- 9 RMON Configuration 105
- RMON Groups 106
- Alarm group 107
- Private alarm group 107
- Configuration Procedure 109
- Configuration Prerequisites 109
- Information Center Overview 115
- System Information Format 120
- 11 NQA Configuration 136
- Basic NQA concepts 139
- NQA Configuration Task List 140
- Configuring the NQA Server 141
- Enabling the NQA Client 141
- Creating an NQA Test Group 142
- Configuring DHCP Tests 143
- Configuring DNS Tests 144
- Configuring FTP Tests 145
- Configuring HTTP Tests 146
- Configuring UDP Jitter Tests 147
- Configuration prerequisites 148
- Configuring UDP jitter tests 148
- Configuring SNMP Tests 149
- Configuring TCP Tests 150
- Configuring UDP Echo Tests 150
- Configuring UDP echo tests 151
- Configuring Voice Tests 152
- Scheduling an NQA Test Group 157
- NQA Configuration Examples 158
- 12 Index 178
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX6000 Series Access Controllers
(85 pages)
(13 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels