H3c-technologies H3C WX5000 Series Access Controllers Manuel d'utilisateur

H3C WX5002V2 Access ControllerInstallation ManualHangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: 6PW101-20130128

1-4 Item Description Max input voltage range For AC power input: 90 VAC to 264 VAC, 47 Hz to 63 Hz For DC power input: –36 VDC to –72 VDC Power cons

1-5 LEDs Silkscreen Status Description Solid green The system is performing POST or downloading software. Green, slow blinking (1 Hz) The system w

1-6 RJ-45 Signal Direction DB-9 3 TXD ← 3 4 CD → 1 5 GND — 5 6 RXD → 2 7 DSR → 6 8 CTS → 8 Ethernet interfaces 1) Introduction The WX5002V2 provi

1-7 Table 1-9 Technical specifications for the GE optical interface modules Description Item Short-haul multimode (850 nm) SFP module Medium-haul sin

1-8 The Ethernet optical interfaces of the WX5002V2 support LC connectors only. Figure 1-7 LC connector z Before using an optical fiber to connec

1-9 RJ-45 Signal Category-5 twisted pair Signal direction RJ-45 7 — White (Brown) — 7 8 — Brown — 8 Table 1-11 Crossover cable pinouts RJ-45 Si

2-1 2 Installation Preparation Safety Precautions Installation and removal of the unit and its accessories must be carried out by qualified person

2-2 Installation Site Checking The WX5002V2 must be used indoors. You can mount the WX5002V2 in a cabinet or on a workbench, but make sure that: z A

2-3 metallic corrosion and the aging process of some parts. The specific limits of the harmful gases such as are given in the following table. Table

2-4 3) Lock the terminal of the alligator clip to the ESD-preventive wrist strap. 4) Attach the alligator clip to the rack where the access control

Copyright © 2009-2013, Hangzhou H3C Technologies Co., Ltd. and its licensors All Rights Reserved No part of this manual may be reproduced or transmi

2-5 Do not stare the laser beam of an optical fiber. Otherwise, your eyes may be hurt. Installation Tools z Flat-blade screwdriver z Phillips scr

3-1 3 Installation When you ask your sales agent to maintain your access controller, you must ensure that the dismantlement-preventive seal on a m

3-2 The WX5002V2 can be installed in either a standard 19-inch rack or a workbench as needed. Installing the Access Controller onto a 19-Inch Rack Th

3-3 Figure 3-4 Install front mounting brackets to both sides of the access controller 3) Take out the bearing screws, which are packaged with rear

3-4 5) Support the bottom of your access controller with one hand and hold the front part of the access controller with the other hand, and then gen

3-5 7) Use screws and the corresponding cage nuts to fix the front mounting brackets to the front square-hole rack rails, so that the front and rear

3-6 Figure 3-10 Install a tray 4) Place the access controller on the tray horizontally, gently push the access controller into the rack along the

3-7 Slide rail appearance Figure 3-12 Appearance of a slide rail (1) Slotted hole, a screw hole for fixing the slide rail to the rear round-hole rac

3-8 Figure 3-14 Installation with front mounting brackets and slide rails 5) Use M6 screws and cage nuts to fix the front mounting brackets to the

3-9 Make sure that there is at least 1 U (44.45 mm, 1.75 in.) height away from neighbor devices for heat dissipation. Installing the Access Contro

About This Manual Organization The H3C WX5002V2 documentation set includes: Category Documents Purposes Marketing brochures Describe product specif

3-10 Figure 3-16 Ground the access controller through a grounding strip (1) AC power socket (2) Grounding terminal (3) PGND wire (4) Grounding str

3-11 This method applies to the device using AC power input. If the access controller is AC powered, you can ground the access controller through

3-12 Figure 3-19 Install the AC power cord retainer (1) Rear panel (2) Power cord retainer slot (3) AC power cord retainer (4) AC power cord 5)

3-13 Connecting Interface Cables Connecting the Console Cable 1) Select a terminal for configuration. The terminal can be a character terminal with

3-14 Connecting the Ethernet Cable To an the Ethernet electrical interface 1) Connect one end of the Ethernet cable to an Ethernet electrical interf

3-15 3) Power on the access controller and check the SFP interface LEDs. For description on SFP LED status, refer to section “LEDs” on page 1-4.

4-1 4 Initial Startup Setting up the Configuration Environment Connecting a Configuration Terminal to the Access Controller For how to connect a con

4-2 Figure 4-2 Select the serial interface used for HyperTerminal connection Step4 Click OK and the system displays the following interface, as sho

4-3 Figure 4-4 HyperTerminal window Step6 Set HyperTerminal properties. Select File > Properties > Settings in the HyperTerminal to enter the

4-4 Powering on the Access Controller After the access controller is powered on, the system first initializes memory. After the initiation, the syste

Symbols Convention Description Means reader be extremely careful. Improper operation may cause bodily injury. Means reader be careful. Improper op

4-5 Starting to get the main application file--cfa0:/main.bin!... ... The main appl

5-1 5 Software Maintenance Overview Files Managed by the Access Controller The WX5002V2 manages the following three types of files: z BootWare prog

5-2 The default names and types of the application files and their loading priorities for booting are as follows. z Main application file. The defau

5-3 Approaches for Software Maintenance You can maintain the access controller in one of the following three ways: z Upgrade BootWare and applicati

5-4 BootWare and Application File Upgrade Flow Figure 5-1 BootWare and application file upgrade flow StartCheck the Comwareapplication versionSelect

5-5 **************************************************************************** Copyright (c) 2004-2009 Hangzhou H3C Technologies Co., Ltd. Compile

5-6 Enter your choice(0-9): BootWare Submenus Serial submenu You can upgrade application files, change the serial interface baud rate, and so on thro

5-7 BootWare operation submenu Enter 7 on the BootWare main menu to enter the BootWare operation submenu. The system displays: ======================

5-8 z The BootWare program is upgraded together with the Comware application. When you upgrade the Comware application program, the system automati

5-9 Figure 5-2 Disconnect the terminal Select File > Properties, In the Properties dialog box, click Configure… and then Set the Bits per secon

i Table of Contents 1 Access Controller Overview...

5-10 Then, press the Enter key, and the system will prompt the current baud rate. The current baudrate is 115200 bps ==============================&

5-11 Load File Name :host :main.bin Target File Name :target :main.bin Server IP Address

5-12 |Note:the operating device is cfa0 | |<1> Backup Full BootWare

5-13 |<4> 57600 | |<5> 115200

5-14 Figure 5-5 Send File dialog box Click Browse… to select the application file to be downloaded, and select Xmodem from the Protocol drop-down l

5-15 z The actual file name, size and path may differ from what are shown in the figure above. Before upgrading the software of your access control

5-16 Enter 3 on the BootWare main menu to enter the Ethernet submenu. Then, enter 5 on the submenu to enter the Ethernet interface configuration inte

5-17 Connect GigabitEthernet 1/0/1 to a PC with an Ethernet cable. Run TFTP Server on the PC, and set the path of the application file to be download

5-18 Maintaining the Application and Configuration Files Through the CLI After the access controller is normally started, you can back up and restore

5-19 <H3C>tftp 192.168.0.1 put startup.cfg config.bak File will be transferred in binary mode Sending file to remote TFTP server. Please w

ii Setting Terminal Parameters...4-1 Powering

5-20 Figure 5-9 Set up a software maintenance environment (the access controller as the FTP server) PCFTP ClientACFTP ServerConsoleEthernet Configur

5-21 226 Transfer complete. ftp: 14323376 bytes received in 16.81Seconds 851.87Kbytes/sec. To restore the backup file to the access controller, do th

5-22 227 Entering passive mode (192,168,0,1,5,60) 125 Using existing data connection 226 Closing data connection; File transfer successful. FTP: 1

5-23 3 -rw- 76960 Aug 15 2008 15:58:02 vmetest.vme 252434 KB total (242996 KB free) File system type of cfa0: FAT32 Setting an Applic

5-24 Specifying a Startup Configuration File Using the CLI You can use the startup saved-configuration cfgfile command to specify the configure file

5-25 z /unreserved: Permanently deletes the specified file, and the deleted file can never be restored. z file-url: Name of the file to be deleted.

5-26 [H3C] save After modifying the user password, use the save command to save it. BootWare Password Loss Contact your local dealer if you forget

5-27 To back up the basic and extended BootWare to the CF card, enter 1 on the BootWare operation submenu and follow the prompts: Will you backup the

6-1 6 Troubleshooting Software Loading Failure If software loading fails, the system runs the old version of the software. The following information

6-2 Configuration System Failure If the access controller is operational upon power-on, the configuration terminal displays the boot information; oth

1-1 1 Access Controller Overview Introduction The H3C WX5002V2 Access Controller is a new-generation wireless access controller product developed by

i Table of Contents Appendix A Installation of Lightning Arrester for Network Interfaces ··················································A-1 Tools··

A-1 Appendix A Installation of Lightning Arrester for Network Interfaces z You can install a lightning arrester only for each 10/100 Mbps electri

A-2 Technical parameters, installation and maintenance methods of an arrester have been given in the arrester instruction. Read the instruction care

i Table of Contents Appendix B Installation of Lightning Arrester for AC Power·································································· B-1

B-1 Appendix B Installation of Lightning Arrester for AC Power No lightning arrester (lightning protection grounding strip) is supplied with the a

B-2 3) Pay adequate attention if the red LED is on. You should correctly locate the problem, whether it is caused because the ground cable of the ar

i Table of Contents Appendix C Regulatory Compliance Information ····················································································

C-1 Appendix C Regulatory Compliance Information Regulatory compliance standards Table C-1 Regulatory compliance standards Discipline Standards EMC

C-2 WEEE Directive–2002/96/EC The products this manual refers to are covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and

C-3 Japan regulatory compliance VCCI These products comply with the requirements of VCCI Class A Information Technology Equipment (ITE). Warning: I

1-2 Figure 1-2 Front panel of the WX5002V2 (1) Gigabit Ethernet interface 2—SFP optical interface (2) 1000 Mbps LED of gigabit Ethernet interface 2

i Table of Contents Appendix D Safety Information Sicherheits informationen安全信息······················································ D-1 Overview Übe

D-1 Appendix D Safety Information Sicherheits informationen 安全信息 Overview Überblick 概述 This section introduces part of the safety precautions that s

D-2 为了避免可能发生的事故，请在进行任何操作前，仔细阅读设备操作手册和本章节的安全规范。手册中 出现的说明、注意、警告、危险，不能涵盖所有的安全预防，仅仅是在整个操作过程中的安全提示和补充。因此，负责安装和日常维护本设备的人员必须具备安全操作基本技能。 操作人员要按照当地的安全规范进行操作。

D-3 为了避免对人和设备造成伤害，请认真执行下列要求： z Read all the instructions before operation. z Lesen Sie alle Anweisungen sorgfältig durch, bevor Sie mit dem Arbeite

D-4 z DC 电源输入：61-72V 电源和 AC 主输入之间的绝缘等级是加强绝缘。 Power Cable Zuleitung 电缆 Installation and removal of live power cable is prohibited strictly. Transien

D-5 Für mit Gleichstrom betriebene Ausrüstung benutzen Sie bitte eine 1.0 mm2 oder 16 AWG Zuleitung. Für mit Wechselstrom betriebene Ausrüstung benu

1-3 Specifications Processor and Storages Table 1-2 Processor and storages of the WX5002V2 Item Description Processor XLR716 (800 MHz) CF card Bui