H3c-technologies H3C WX5500E Series Access Controllers Manuel d'utilisateur Page 74
- Page / 221
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
63
Figure 18 Network diagram and topology of MST region 3
MST region
An MST region consists of multiple devices in a switched network and the network segments among them.
All these devices have the following characteristics:
• A spanning tree protocol is enabled.
• Same region name.
• Same VLAN-to-instance mapping configuration.
• Same MSTP revision level.
• Physically linked together.
Multiple MST regions can exist in a switched network. You can assign multiple devices to the same MST
region. In Figure 17,
the switched network comprises four MST regions (MST region 1 through MST region
4), and all devices in each MST region have the same MST region configuration.
MSTI
MSTP can generate multiple independent spanning trees in an MST region, and each spanning tree is
mapped to specific VLANs. Each spanning tree is called an "MSTI."
In Figure 18, M
ST region 3 comprises three MSTIs: MSTI 1, MSTI 2, and MSTI 0.
VLAN-to-instance mapping table
As an attribute of an MST region, the VLAN-to-instance mapping table describes mapping relationships
between VLANs and MSTIs.
In Figure 18, the VL
AN-to-instance mapping table of MST region 3 is: VLAN 1 to MSTI 1, VLAN 2 and
VLAN 3 to MSTI 2, and other VLANs to MSTI 0. MSTP achieves load balancing by means of the
VLAN-to-instance mapping table.
CST
The CST is a single spanning tree that connects all MST regions in a switched network. If you regard each
MST region as a device, the CST is a spanning tree calculated by these devices through STP or RSTP.
The blue lines in Figure 17 r
epresent the CST.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX5500E Series Access Controllers
(4 pages)
(18 pages)LevelOne 570746 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Switche sieciowe LevelOne 570746.
Dostarczamy 1 pdf podręczników LevelOne 570746 do pobrania za darmo według typów dokumentów: Arkusz Danych
Commentaires sur ces manuels