H3c-technologies H3C WX5500E Series Access Controllers Manuel d'utilisateur Page 194
- Page / 221
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
183
Task Command
Remarks
Display LLDP status of a port.
display lldp status [ interface interface-type
interface-number ] [ | { begin | exclude |
include } regular-expression ]
Available in any view.
Display types of advertisable
optional LLDP TLVs.
display lldp tlv-config [ interface
interface-type interface-number ] [ | { begin |
exclude | include } regular-expression ]
Available in any view.
LLDP configuration examples
Basic LLDP configuration example
Network requirements
As shown in Figure 56, the NMS and Switch A are located in the same Ethernet network. An MED device
and Switch B are connected to GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2 of Switch A.
Enable LLDP globally on Switch A and Switch B to monitor the link between Switch A and Switch B and
the link between Switch A and the MED device on the NMS.
Figure 56 Network diagram
Configuration procedure
1. Configure Switch A:
# Enable LLDP globally.
<SwitchA> system-view
[SwitchA] lldp enable
# Enable LLDP on GigabitEthernet 1/0/1 and GigabitEthernet 1/0/2. (You can skip this step
because LLDP is enabled on ports by default.) Set the LLDP operating mode to Rx.
[SwitchA] interface gigabitethernet 1/0/1
[SwitchA-GigabitEthernet1/0/1] lldp enable
[SwitchA-GigabitEthernet1/0/1] lldp admin-status rx
[SwitchA-GigabitEthernet1/0/1] quit
[SwitchA] interface gigabitethernet 1/0/2
[SwitchA-GigabitEthernet1/0/2] lldp enable
[SwitchA-GigabitEthernet1/0/2] lldp admin-status rx
[SwitchA-GigabitEthernet1/0/2] quit
2. Configure Switch B:
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX5500E Series Access Controllers
(4 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels