H3c-technologies H3C WX5500E Series Access Controllers Manuel d'utilisateur Page 145
- Page / 221
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
134
Ste
p
Command
Remarks
2. Enter VLAN view.
vlan vlan-id
If the specified VLAN does not exist,
this command creates the VLAN
first, and then enters VLAN view.
3. Configure the VLAN as a
super VLAN.
supervlan
By default, no super VLAN is
configured.
4. Associate the super VLAN
with the specified sub-VLANs.
subvlan vlan-list
VLANs specified by vlan-list must be
the sub-VLANs configured earlier.
Configuring a VLAN interface for the super VLAN
This section describes how to configure a VLAN interface for the super VLAN.
To configure a VLAN interface for the super VLAN:
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Create a VLAN interface, and
enter VLAN interface view.
interface vlan-interface
vlan-interface-id
The value of vlan-interface-id must
be the ID of the super VLAN.
3. Configure an IP address for
the VLAN interface of the
super VLAN.
ip address ip-address { mask |
mask-length } [ sub ]
By default, the IP address of a
VLAN interface is not configured.
4. Enable local proxy ARP.
local-proxy-arp enable
By default, local proxy ARP is
disabled.
Displaying and maintaining super VLANs
Task Command
Remarks
Display the mapping between a
super VLAN and its sub-VLANs.
display supervlan [ supervlan-id ] [ | { begin |
exclude | include } regular-expression ]
Available in any
view.
Super VLAN configuration example
Network requirements
As shown in Figure 40:
• Create super VLAN 10, and configure its VLAN interface IP address as 10.0.0.1/24.
• Create sub-VLANs VLAN 2, VLAN 3, and VLAN 5.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX5500E Series Access Controllers
(4 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.084 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels