H3c-technologies H3C WX5500E Series Access Controllers Manuel d'utilisateur Page 209
- Page / 221
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
198
Ste
p
Command
Remarks
5. Configure the Leave timer.
mrp timer leave timer-value
Optional.
The default setting is 60
centiseconds.
6. Configure the Periodic timer.
mrp timer periodic timer-value
Optional.
The default setting is 100
centiseconds.
Table 26 shows the value ranges for Join, Leave, and LeaveAll timers and their dependencies.
• If you set a timer to a value beyond the allowed value range, your configuration will fail. To do that,
you can change the allowed value range by tuning the value of another related timer.
• To restore the default settings of the timers, restore the Join timer first, followed by the Leave and
LeaveAll timers.
Table 26 Dependencies of the Join, Leave, and LeaveAll timers
Timer Lower limit
U
pp
er limit
Join 20 centiseconds Half the Leave timer
Leave Twice the Join timer LeaveAll timer
LeaveAll Leave timer on each port 32760 centiseconds
You can restore the Periodic timer to the default at any time.
Enabling GVRP compatibility
CAUTION:
• MVRP with GVRP compatibility enabled can work to
g
ether with STP or RSTP, but cannot work to
g
ethe
r
with MSTP. When MVRP with GVRP compatibility enabled works with MSTP, the network mi
g
ht operate
improperly.
• When GVRP compatibility is enabled for MVRP, H3C recommends disabling the Period timer.
Otherwise, the VLAN status might frequently change when the system is busy.
MVRP can be compatible with GVRP. When the peer device supports GVRP, you can enable GVRP
compatibility on the local end, so that the local end can receive and send MVRP and GVRP protocol
packets at the same time.
To enable GVRP compatibility:
Ste
p
Command
Remarks
1. Enter system view
system-view N/A
2. Enable GVRP
compatibility
mvrp gvrp-compliance
enable
By default, GVRP compatibility is disabled.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX5500E Series Access Controllers
(4 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels