H3c-technologies H3C WX5500E Series Access Controllers Manuel d'utilisateur Page 140
- Page / 221
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
129
Ste
p
Command
Remarks
1. Enter system view.
system-view N/A
2. Enter VLAN view.
vlan vlan-id N/A
3. Associate an IP subnet with
the VLAN.
ip-subnet-vlan [ ip-subnet-index ]
ip ip-address [ mask ]
The IP subnet or IP address to be
associated with a VLAN cannot be a
multicast subnet or a multicast address.
4. Return to system view.
quit N/A
5. Enter interface view or port
group view.
• Enter Ethernet interface view:
interface interface-type
interface-number
• Enter Layer 2 aggregation
interface view:
interface bridge-aggregation
interface-number
• Enter port group view:
port-group manual
port-group-name
Use one of the commands.
• The configuration made in Ethernet
interface view applies only to the
port.
• The configuration made in port
group view applies to all ports in
the port group.
• The configuration made in Layer 2
aggregate interface view applies to
the aggregate interface and its
aggregation member ports. If the
system fails to apply the
configuration to the aggregate
interface, it stops applying the
configuration to aggregation
member ports. If the system fails to
apply the configuration to an
aggregation member port, it skips
the port and moves to the next
member port.
6. Configure port link type as
hybrid.
port link-type hybrid By default, all ports are access ports.
7. Configure the hybrid ports
to permit the specified IP
subnet-based VLANs to
pass through.
port hybrid vlan vlan-list { tagged
| untagged }
By default, a hybrid port allows only
packets from VLAN 1 to pass through
untagged.
8. Associate the hybrid ports
with the specified IP
subnet-based VLAN.
port hybrid ip-subnet-vlan vlan
vlan-id
By default, no IP subnet-based VLAN is
associated with a port.
Configuration example
Network requirements
As shown in Figure 39, the hosts in the office belong to different IP subnets 192.168.5.0/24 and
192.168.50.0/24.
Configure Device C to transmit packets over separate VLANs based on their source IP addresses.
- H3C WX5540E Access Controller 1
- Switching Engine 1
- Preface 3
- Symbols 4
- Network topology icons 4
- Port numbering in examples 4
- Obtaining documentation 5
- Technical support 5
- Documentation feedback 5
- Contents 6
- Switch A Switch B 14
- Switch C 14
- Enabling auto power-down 17
- Bulk configuring interfaces 30
- Configuring MAC Information 39
- Operational key 44
- Configuration classes 44
- Reference port 44
- Link aggregation modes 45
- Choosing a reference port 46
- Configuring port isolation 63
- STP protocol packets 65
- Basic concepts in STP 66
- Path cost 67
- STP timers 71
- MSTP features 73
- MSTP basic concepts 73
- MST region 74
- Regional root 75
- Common root bridge 75
- Port roles 75
- How MSTP works 76
- STP configuration task list 78
- RSTP configuration task list 79
- PVST configuration task list 80
- MSTP configuration task list 81
- Configuring an MST region 82
- Configuring edge ports 89
- Performing mCheck 96
- Configuring digest snooping 97
- <DeviceB> system-view 99
- Configuration prerequisites 100
- Configuration procedure 100
- Configuration example 101
- Enabling BPDU guard 101
- Enabling root guard 102
- Enabling loop guard 102
- Enabling TC-BPDU guard 103
- Enabling BPDU drop 104
- MSTP configuration example 105
- PVST configuration example 109
- Configuring BPDU tunneling 113
- Enabling BPDU tunneling 116
- Network requirements 117
- Configuring VLANs 120
- VLAN frame encapsulation 121
- VLAN types 122
- Protocols and standards 122
- Configuring port-based VLANs 125
- Frame handling on a port 126
- Verifying the configuration 130
- Configuring MAC-based VLANs 131
- Configuration considerations 136
- Configuration guidelines 142
- Task Command 143
- Remarks 143
- Configuring super VLANs 144
- Name: VLAN 0005 148
- Tagged Ports: none 148
- Untagged Ports: 148
- Configuring voice VLANs 158
- VLAN assignment mode 162
- Configuring GVRP 169
- GARP timers 170
- GARP PDU format 171
- Introduction to GVRP 172
- GVRP registration modes 172
- GVRP configuration task list 173
- Configuring GVRP functions 173
- Configuring the GARP timers 174
- GVRP configuration examples 176
- Configuring LLDP 181
- LLDPDUs 182
- LLDP-MED TLVs 184
- Working mechanism 185
- LLDP configuration task list 186
- Enabling LLDP polling 188
- Configuring LLDP trapping 193
- LLDP configuration examples 194
- Overview 199
- Configuring MVRP 203
- MRP messages 204
- MRP timers 205
- MVRP configuration task list 206
- Enabling MVRP 207
- Configuring MRP timers 208
- Enabling GVRP compatibility 209
- Configuring Device B 212
- Configuring Device C 213
- Configuring Device D 214
- 1(default), 10 219
Produits connexes et manuels pour Routeurs H3c-technologies H3C WX5500E Series Access Controllers
(4 pages)
(18 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels